Campfire Wilds

The finished picture

Thick lines are baseplate edges, thin lines are the 16×16 sections. Select a section with artwork in it to open its step.

0 of 45 sections built

160 × 160 studs, 128.0 × 128.0 cm. It tiles exactly onto 25 white 32×32 baseplates.

Piece list

All studs are Plate 1×1, part 3024. The number in each swatch is the code used in the build steps. The order quantity adds spares, because 1×1 plates go missing.

Also needed

• 25 × white 32×32 baseplate (LEGO Classic 11026). White matters here because the background shows.
• Backing board, 1280 × 1280 mm. 9 to 12 mm MDF or plywood, plus strong double-sided tape or grab adhesive to fix the baseplates to it.
• Brick separator for lifting misplaced plates, and 6 small tubs for sorting.
• A few 2×4 bricks to bridge the joins between baseplates while you line them up.
• Optional flat background: 23,245 more studs to cover in White (BrickLink colour 1). Larger white plates such as 2×8 or 4×8 cover the open areas far faster than 1×1s.

Rough cost

Baseplates are the main cost: £7.99 each at UK retail, so £199.75 for 25. The plates are minor by comparison. New 1×1 plates were listed at about US$0.018 to $0.028 each, which puts them at roughly US$45 to $70.

Baseplate price from brickfact on 11 October 2026. The plate price is one Brick Owl check on a different colour of the same part, so treat the plate figure as a guide and add postage.

Before you build

1. Order the plates by part number 3024 and the colour names above from BrickLink or Brick Owl. The wanted list above uploads straight into BrickLink. Confirm stock before paying.
2. Sort the plates into tubs and label each tub with its code.
3. Lay the 25 baseplates out 5 wide and 5 high and number them on the back, left to right, top row first.
4. Build each baseplate on a table before mounting. Each baseplate has four 16×16 sections. Sections with no artwork are skipped, so the steps jump straight to the next one that needs plates.
5. On a bare baseplate there are no guide lines. Count studs from the corner of the section, place the darkest shapes first, then fill in around them.
6. After every section, press the plates down with a flat book and tick the step off here.

Build steps

,

Plates for this step

Squares with a dot stay as bare baseplate. Count in from the top-left corner of the section using the row and column numbers.

Finishing

1. Cut the backing board to 1280 × 1280 mm, or larger if you want a border for a frame.
2. Fix baseplate 1 square to the top-left corner. Butt the next baseplate tight against it and clip two or three 2×4 bricks across the join before the adhesive grabs, so the stud spacing carries across. Repeat for the rest.
3. Remove the bridging bricks and check that shapes crossing a join, such as the wolf and the mountain ranges, line up.
4. Hang it from fixings screwed into the board. At this size the board is the heavy part, so use wall fixings rated for it.

What changed from the artwork

• Nothing is resized. The picture is 160 × 160 pixels and every pixel is one stud, so the thin lines and checker patterns survive exactly.
• Nine shades become six LEGO colours. The warm greys turn slightly cooler, the beige becomes Tan, the flames are Red with Orange centres, and the wolf’s eye is Red.
• The artwork sits one plate proud of the bare white studs around it, which gives a slight relief. For a flat surface, fill the background with white plates using the count under the piece list.
• It does not shrink well. Halving it breaks the one-pixel lines, so for something smaller build a single motif instead: a tree or rock fits one 16 × 16 section, and a campfire with its smoke fits two.